electronics engineer interview question 02
45. Explain 5-4-3 rule
In a Ethernet network, between any two points on the network, there can be no more than five network segments or four repeaters, and of those five segments only three of segments can be populated.
46. Explain the difference between TFTP and FTP application layer protocols
The Trivial File Transfer Protocol (TFTP) allows a local host to obtain files from a remote host but does not provide reliability or security. It uses the fundamental packet delivery services offered by UDP.
The File Transfer Protocol (FTP) is the standard mechanism provided by TCP / IP for copying a file from one host to another. It uses the services offered by TCP and so is reliable and secure. It establishes two connections (virtual circuits) between the hosts, one for data transfer and another for control information.
47. Explain the range of addresses in the classes of internet addresses
Class A 0.0.0.0 – 127.255.255.255
Class B 22.214.171.124 – 126.96.36.199
Class C 192.0.0.0 – 188.8.131.52
Class D 184.108.40.206 – 220.127.116.11
Class E 240.0.0.0 – 247.255.255.255
48. Explain the minimum and maximum length of the header in the TCP segment and IP datagram
The header should have a minimum length of 20 bytes and can have a maximum length of 60 bytes.
49. Explain difference between ARP and RARP
The address resolution protocol (ARP) is used to associate the 32 bit IP address with the 48 bit physical address, used by a host or a router to find the physical address of another host on its network by sending a ARP query packet that includes the IP address of the receiver. The reverse address resolution protocol (RARP) allows a host to discover its Internet address when it knows only its physical address.
50. Explain ICMP
ICMP is Internet Control Message Protocol, a network layer protocol of the TCP/IP suite used by hosts and gateways to send notification of datagram problems back to the sender. It uses the echo test / reply to test whether a destination is reachable and responding. It also handles both control and error messages.
51. What are the data units at different layers of the TCP / IP protocol suite
The data unit created at the application layer is called a message, at the transport layer the data unit created is called either a segment or an user datagram, at the network layer the data unit created is called the datagram, at the data link layer the datagram is encapsulated in to a frame and
finally transmitted as signals along the transmission media.
52. Explain Project 802
It is a project started by research to set standards that enable intercommunication between equipment from a variety of manufacturers. It is a way for specifying functions of the physical layer, the data link layer and to some extent the network layer to allow for interconnectivity of major LAN protocols.
It consists of the following:
802.1 is an internetworking standard for compatibility of different LANs and MANs across protocols.
802.2 Logical link control (LLC) is the upper sublayer of the data link layer which is non-architecture-specific, that is remains the same for all research-defined LANs.
Media access control (MAC) is the lower sublayer of the data link layer that contains some distinct modules each carrying proprietary information specific to the LAN product being used. The modules are Ethernet LAN (802.3), Token ring LAN (802.4), Token bus LAN (802.5).
802.6 is distributed queue dual bus (DQDB) designed to be used in MANs.
53. Explain Bandwidth
Every line has an upper limit and a lower limit on the frequency of signals it can carry. This limited range is called the bandwidth.
54. Difference between bit rate and baud rate.
Bit rate is the number of bits transmitted during one second whereas baud rate refers to the number of signal units per second that are required to represent those bits. baud rate = bit rate / N where N is no-of-bits represented by each signal shift.
55. Explain MAC address
The address for a device as it is identified at the Media Access Control (MAC) layer in the network architecture. MAC address is usually stored in ROM on the network adapter card and is unique.
56. Explain attenuation
The degeneration of a signal over distance on a network cable is called attenuation.